Warne Scope Rings 1 Inch, Medium Height, Grooved Receiver, Matte Black
Item No.721M
Warne 1" Grooved Receiver Rings, Med. Height The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best f
Price $40
price per Set
excl. tax
6
In stock
Set
Description
Warne 1" Grooved Receiver Rings, Med. Height
The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best fit.
Made in the U.S.A.
• All steel rings with a horizontally split design and only ½” wide.
• Asymetrical reversible side clamp fits a 3/8" or 11mm dovetail.
• Securely mounts to firearm with Torx style T-15 socket cap screws, 25 in/lb. of torque recommended.
Specs:
Color: Matte Black
Ring Height: Medium
Fits Objective Size (General Range - can vary): 20 - 42mm objective
Dimension A: 1 inch
Dimension B: .400" (measurement is from the top of the dovetail to the bottom of the scope tube)
Dimension C: .502"
(refer to picture above for dimensions A, B, & C)
Weight (per pair): 3.2oz.
Instructions:
Remove ring top screws and top half of ring. Loosen clamp screw or lever and place directly on grooved receiver. Tighten clamp# screws or levers with rings in approximate location on receiver.
Place scope in the rings and adjust ring location if needed. Snap ring tops over scope tube and start ring top screws. Adjust scope for proper eye relief and level reticle. Tighten ring top screws to 25 in/lb* max. Tighten clamp screws to 25 in/lb* max or tighten levers thumb & forefinger tight. (there is no need to over tighten QD lever)
*Torque Specs are for dry threads - do not use threadlocker material.
#Rings are factory set for 3/8" dovetail (dimple up), for 11mm dovetails, remove clamp and re-install with the dimple down.
The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best fit.
Made in the U.S.A.
• All steel rings with a horizontally split design and only ½” wide.
• Asymetrical reversible side clamp fits a 3/8" or 11mm dovetail.
• Securely mounts to firearm with Torx style T-15 socket cap screws, 25 in/lb. of torque recommended.
Specs:
Color: Matte Black
Ring Height: Medium
Fits Objective Size (General Range - can vary): 20 - 42mm objective
Dimension A: 1 inch
Dimension B: .400" (measurement is from the top of the dovetail to the bottom of the scope tube)
Dimension C: .502"
(refer to picture above for dimensions A, B, & C)
Weight (per pair): 3.2oz.
Instructions:
Remove ring top screws and top half of ring. Loosen clamp screw or lever and place directly on grooved receiver. Tighten clamp# screws or levers with rings in approximate location on receiver.
Place scope in the rings and adjust ring location if needed. Snap ring tops over scope tube and start ring top screws. Adjust scope for proper eye relief and level reticle. Tighten ring top screws to 25 in/lb* max. Tighten clamp screws to 25 in/lb* max or tighten levers thumb & forefinger tight. (there is no need to over tighten QD lever)
*Torque Specs are for dry threads - do not use threadlocker material.
#Rings are factory set for 3/8" dovetail (dimple up), for 11mm dovetails, remove clamp and re-install with the dimple down.
Reviews (0)
There are no reviews yet.
Related Items
Warne Scope Rings 1 Inch, Medium Height, Grooved Receiver, Matte Black
Item No.721M
Warne 1" Grooved Receiver Rings, Med. Height The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best f
Price $40
price per Set
excl. tax
6
In stock
Set
Description
Warne 1" Grooved Receiver Rings, Med. Height
The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best fit.
Made in the U.S.A.
• All steel rings with a horizontally split design and only ½” wide.
• Asymetrical reversible side clamp fits a 3/8" or 11mm dovetail.
• Securely mounts to firearm with Torx style T-15 socket cap screws, 25 in/lb. of torque recommended.
Specs:
Color: Matte Black
Ring Height: Medium
Fits Objective Size (General Range - can vary): 20 - 42mm objective
Dimension A: 1 inch
Dimension B: .400" (measurement is from the top of the dovetail to the bottom of the scope tube)
Dimension C: .502"
(refer to picture above for dimensions A, B, & C)
Weight (per pair): 3.2oz.
Instructions:
Remove ring top screws and top half of ring. Loosen clamp screw or lever and place directly on grooved receiver. Tighten clamp# screws or levers with rings in approximate location on receiver.
Place scope in the rings and adjust ring location if needed. Snap ring tops over scope tube and start ring top screws. Adjust scope for proper eye relief and level reticle. Tighten ring top screws to 25 in/lb* max. Tighten clamp screws to 25 in/lb* max or tighten levers thumb & forefinger tight. (there is no need to over tighten QD lever)
*Torque Specs are for dry threads - do not use threadlocker material.
#Rings are factory set for 3/8" dovetail (dimple up), for 11mm dovetails, remove clamp and re-install with the dimple down.
The Rimfire rings are designed to fit a very wide selection of rifles with either a 3/8" or 11mm dovetail. This is made possible by using a solid asymmetrical reversible clamp that can be flipped 180° and used on wider or narrower dovetails for the best fit.
Made in the U.S.A.
• All steel rings with a horizontally split design and only ½” wide.
• Asymetrical reversible side clamp fits a 3/8" or 11mm dovetail.
• Securely mounts to firearm with Torx style T-15 socket cap screws, 25 in/lb. of torque recommended.
Specs:
Color: Matte Black
Ring Height: Medium
Fits Objective Size (General Range - can vary): 20 - 42mm objective
Dimension A: 1 inch
Dimension B: .400" (measurement is from the top of the dovetail to the bottom of the scope tube)
Dimension C: .502"
(refer to picture above for dimensions A, B, & C)
Weight (per pair): 3.2oz.
Instructions:
Remove ring top screws and top half of ring. Loosen clamp screw or lever and place directly on grooved receiver. Tighten clamp# screws or levers with rings in approximate location on receiver.
Place scope in the rings and adjust ring location if needed. Snap ring tops over scope tube and start ring top screws. Adjust scope for proper eye relief and level reticle. Tighten ring top screws to 25 in/lb* max. Tighten clamp screws to 25 in/lb* max or tighten levers thumb & forefinger tight. (there is no need to over tighten QD lever)
*Torque Specs are for dry threads - do not use threadlocker material.
#Rings are factory set for 3/8" dovetail (dimple up), for 11mm dovetails, remove clamp and re-install with the dimple down.
Reviews (0)
There are no reviews yet.